Make your Starlink cable connection easier to access with a 1-metre Ethernet adapter featuring a weather-protected RJ45 coupler. According to the supplier, the adapter is designed for Starlink Gen 3/Standard V3 and Starlink Mini, allowing a separate network cable to connect through a protected junction.
The cable has an RJ45 male plug with a sealing connector profile at one end and an RJ45 female socket with a screw-on protective housing at the other. The housing encloses the connected Ethernet plug, while the cable seal helps protect the joint against moisture and dirt. The supplier states IP68 protection for the correctly assembled connection.
With a length of 1 metre, equivalent to 1000 mm, the adapter moves the connection point away from the device. This is useful when the original port is difficult to reach or when you want to disconnect a longer cable without repeatedly unplugging the connection at the Starlink equipment.
It is a practical accessory for setups that are regularly assembled and packed away, including motorhomes, camping and temporary installations. It can also provide a more accessible connection point in a fixed installation.
The protective housing includes sealing rings, a cable seal and a protective cap for the female socket. To achieve the intended protection, the parts must be assembled in the correct order and the seal must fit the connected cable’s outer diameter. Close the protective cap when the socket is not in use.
A convenient adapter for combining a flexible cable connection with a protected RJ45 joint. Check the connector fit for your Starlink model and choose an extension cable that meets both the installation’s electrical requirements and the coupler’s sealing requirements.
✅ Benefits
- 1-metre adapter cable – moves the connection point away from the device for easier access.
- RJ45 male to female – connects a separate Ethernet cable.
- Weather-protected joint – screw-on housing with seals around the connection.
- Stated IP68 rating – applies when correctly assembled with a compatible cable.
- Convenient disconnection – useful for transport and temporary setups.
- Protective socket cap – protects the female connection when unused.
- No software required – a passive cable adapter for compatible connections.
🎯 Ideal for
- Starlink Gen 3/Standard V3 and Mini, according to the supplier’s compatibility information.
- Motorhomes and camping, where cables need to be connected and disconnected.
- Installations with hard-to-reach network ports.
- Protected outdoor Ethernet joints, with correct assembly and sealing.
- Connecting a separate Ethernet cable through an accessible RJ45 female socket.
🔧 Connection and use
Check that the adapter plug’s shape and seal fit the port on your Starlink device.
Slide the cable gland nut, cable seal and protective housing over the Ethernet cable to be connected. Follow the assembly order in the product instructions.
Insert the cable’s RJ45 male plug into the adapter’s female socket until it locks. Assemble the protective housing, position the cable seal correctly and tighten the gland nut.
Check that the seal closes around the cable and that all sealing rings are seated correctly. IP68 protection depends on a compatible cable diameter and correct assembly. Fit the protective cap when the socket is unused.
Connect the adapter’s male plug to the compatible Starlink port and test the connection. Avoid strain on connectors and sharp cable bends.
This adapter is not a PoE injector or voltage converter. If used in a powered Starlink cable run, the complete installation must meet the equipment’s requirements. Starlink Mini still requires its separate power supply.
📡 Capacity and connections
| Feature | Details |
|---|
| Function | Passive Ethernet adapter and cable coupler |
| Stated compatibility | Starlink Gen 3/Standard V3 and Mini |
| Connection 1 | RJ45 male with sealing connector profile |
| Connection 2 | RJ45 female in protective housing |
| Contact positions | 8 |
| Cable length | 1 m / 100 cm / 1000 mm |
| Coupler design | Screw-on housing with cable seal |
| Protective cap | For the female socket |
| Active electronics | No |
⚙️ Technical specifications
| Feature | Specification |
|---|
| Product type | Ethernet adapter cable |
| Configuration | Male to female |
| Stated protection rating | IP68 when correctly assembled |
| Coupler size | M20, according to product images |
| Listed materials | PVC and nylon |
| Colour | Black |
| Cable length | 1000 mm |
| Quantity | 1 |
📦 Package contents
- 1 × 1 m Ethernet adapter cable with RJ45 male and female connections.
- Protective housing and seals for the cable joint.
- Protective cap for the female socket.
Starlink equipment and a separate Ethernet cable are not included.
