Inverto Black Pro Single Monoblock LNB 3° – 2 Satellites and 1 Receiver | 60 mm

The Inverto Black Pro Single Monoblock 3° is a Universal Monoblock LNB designed for simultaneous reception from two satellite positions separated by approximately 3°. It provides a practical solution when the satellites are too closely spaced for two conventional LNBs to fit beside each other in a standard multi-feed holder.

The product combines two Universal LNBs and an integrated DiSEqC 1.0 switch in one unit. It has one output and is intended for one satellite receiver or tuner, which can switch between both satellite positions.

The LNB is suitable for combinations such as Hotbird 13°E with Eutelsat 16°E or Eutelsat 16°E with Astra 19.2°E, provided the satellite dish, its geometry and the installation location are suitable.

The product uses a special 60 mm Monoblock mount and requires a compatible LNB holder. The recommended mounting accessory is product number 1326, sold separately.

With a typical noise figure of 0.2 dB, gain of 50–65 dB and good frequency stability, the LNB is suitable for digital satellite television, DVB-S2 and HDTV.

✅ Product Benefits

• Receives two satellite positions separated by approximately 3°

• Designed for satellites positioned very close together

• One output for one receiver or tuner

• Two Universal LNBs in one compact unit

• Integrated DiSEqC 1.0 switch

• No separate external DiSEqC switch required

• Suitable for Hotbird 13°E and Eutelsat 16°E

• Also suitable for Eutelsat 16°E and Astra 19.2°E when correctly installed

• Typical noise figure of 0.2 dB

• Gain of 50–65 dB

• Good frequency stability

• Cross-polarisation isolation of at least 22 dB

• DVB-S2- and HDTV-compatible

• Designed for dishes measuring approximately 75–85 cm

• Operating temperature from −30 to +60°C

🎯 Ideal For

• Hotbird 13°E and Eutelsat 16°E

• Eutelsat 16°E and Astra 19.2°E

• Two satellites separated by approximately 3°

• Installations where two conventional LNBs cannot fit

• One satellite receiver

• Televisions with an integrated satellite tuner

• Single Tuner receivers

• Satellite dishes measuring approximately 75–85 cm

• DVB-S2 and HDTV reception

• Installations using a compatible 60 mm Monoblock holder

🔧 Connection and Operation

The LNB has one F-output, which connects by coaxial cable to a satellite receiver or television with an integrated DVB-S/DVB-S2 tuner.

The connected tuner controls:

• Satellite-position selection through DiSEqC 1.0

• Vertical or horizontal polarisation through the supply voltage

• Low or high band through the 0/22 kHz signal

The standard configuration is:

• Satellite A / DiSEqC port A: Eastern satellite position

• Satellite B / DiSEqC port B: Western satellite position

Satellite A is the default position. Depending on the receiver, the ports may also be identified as Port 1/2, A/B or AA/AB.

As the product has only one output, it is intended for one independent tuner. A Twin Tuner receiver normally requires two separate LNB outputs for full independent operation.

📡 Example Satellite Combinations

Please note: These combinations are installation examples. Reception cannot be guaranteed at every location because performance depends on satellite signal strength, dish design and local reception conditions.

🛰️ Mounting and Dish Size

The product has a 60 mm Monoblock mount and does not fit directly into a conventional 40 mm LNB holder.

Correct installation requires:

• A special 60 mm Monoblock holder

• Recommended holder: product number 1326

• A satellite dish measuring approximately 75–85 cm

• Recommended F/D ratio: 0.6

• Accurate elevation, azimuth and skew adjustment

The special holder, product number 1326, is not included and must be ordered separately.

⚙️ Technical Specifications

Product type: Universal Single Monoblock LNB

Series: Inverto Black Pro

Satellite positions: 2

Satellite separation: Approximately 3°

Users/tuners: 1

Number of outputs: 1

Satellite selection: DiSEqC 1.0

Satellite A: Eastern satellite position and default position

Satellite B: Western satellite position

Low-band input frequency: 10.70–11.70 GHz

Low-band output frequency: 950–1950 MHz

Low-band LO frequency: 9.75 GHz

High-band input frequency: 11.70–12.75 GHz

High-band output frequency: 1100–2150 MHz

High-band LO frequency: 10.60 GHz

Typical noise figure: 0.2 dB

Maximum noise figure: 0.7 dB

Initial LO accuracy: ±1.0 MHz max.

LO temperature drift: ±3.0 MHz max.

LO phase noise at 10 kHz: −90 dBc/Hz max.

Conversion gain: 50–65 dB

Gain ripple over 26 MHz: ±0.75 dB

Full-band gain variation: ±4 dB max.

Image rejection: Minimum 40 dB

1 dB compression point at output: Minimum 0.0 dBm

Cross-polarisation isolation: Minimum 22 dB

Output VSWR: 2.5:1

In-band spurious level: −60 dBm max.

Power consumption: Maximum 120 mA at 11–20V

Output impedance: 75Ω

Output connection: 1 × F-female

Mounting diameter: 60 mm

Recommended dish size: 75–85 cm

Recommended F/D ratio: 0.6

Operating temperature: −30 to +60°C

Weight: 220 g

DVB-S2-compatible: Yes

HDTV-compatible: Yes

📦 Package Contents

• 1 × Inverto Black Pro Single Monoblock LNB 3° with 60 mm mounting