The GT-SAT GT-DC2 dController is a professional programming and diagnostic tool for compatible GT-SAT dCSS products. It can be used to configure, check and update compatible Unicable LNBs and multiswitches.
Using a Windows computer and compatible GT-SAT software, installers can transfer configuration settings, perform diagnostic tests and retrieve information from connected equipment. This simplifies troubleshooting and helps confirm that an LNB or multiswitch has been programmed correctly.
The GT-DC2 includes internal memory, allowing a configuration file to be prepared on a computer and stored in the programmer. The saved configuration can subsequently be transferred to a compatible device by pressing the dedicated Program button. A laptop therefore does not always need to be taken to the installation site.
Clear LED indicators display operating status, 0/22 kHz, 13/18V, active and completed transfers, transmission errors, low voltage and short circuits. Its compact, robust construction makes the GT-DC2 particularly suitable for professional installers and service technicians.
✅ Product Benefits
Professional tool for compatible GT-SAT dCSS products
Programs compatible Unicable LNBs and multiswitches
Supports EN50494, EN50607 and dHello
DiSEqC 2.0 communication
Connects to a Windows computer via USB
Performs diagnostic tests
Retrieves diagnostic and installation information
Supports configuration and firmware updates
Internal memory for prepared configuration files
Dedicated Program button for on-site transfer
Can be used without a computer after storing a configuration
Clear LED indicators for status and troubleshooting
Satellite IF loop-through
Can be powered by a 12V mains adapter
Compact and robust enclosure
🎯 Ideal For
Professional satellite installers
Antenna and telecommunications technicians
Configuration of compatible GT-SAT dCSS LNBs
Programming compatible GT-SAT multiswitches
Unicable I installations
Unicable II and dCSS installations
Satellite system servicing and troubleshooting
Preparing multiple devices with the same configuration
Installations where a laptop cannot be used on site
Workshop, service vehicle and field installation work
🔧 Operation and Connection
The GT-DC2 connects to a Windows computer via USB when a new configuration needs to be created, stored or transferred. The compatible GT-SAT product is connected to the programmer’s F-connector marked LNB.
The F-connector marked Receiver provides loop-through for the satellite IF signal. The specified loop-through signal loss is no more than 5 dB.
Once a configuration has been stored in the unit’s internal memory, it can be transferred to a compatible LNB or multiswitch using the Program button. This allows programming to be completed at the installation site without keeping the computer connected.
The unit can be powered using the supplied 12V mains adapter or with 13–18V from a compatible satellite receiver.
Always confirm that the connected LNB or multiswitch is specifically compatible with the GT-DC2 before programming or updating it.
💡 LED Indicators
The GT-DC2 provides indicators for the following functions and status messages:
0/22 kHz: Current band-control signal
Busy: Programming or communication in progress
Done: Transfer completed
F1/F0: Function or communication status
13/18V: Current output voltage
Transmission error: Data transfer error
Vout low: Output voltage too low
Vin low: Input voltage too low
Short-circuit: Short circuit detected
On/Off: Operating status
⚙️ Technical Specifications
Product type: Programming and diagnostic tool
Model: GT-DC2 dController
Compatibility: Compatible GT-SAT dCSS products
Application: Programming, configuration, diagnostics and updates
Supported protocols: EN50494, EN50607 and dHello
Communication with dCSS product: DiSEqC 2.0
Computer connection: USB Type-B
Software operating system: Windows
Internal memory: Yes
Program button: Yes
Satellite IF input: 1 × F-connector
Loop-through output: 1 × F-connector
RF loop-through: Yes
Loop-through signal loss: Maximum 5 dB
External power supply: 12V DC
Alternative power supply: 13–18V from a compatible receiver
Status indication: LED
Enclosure: Compact and robust
Product number: 13525
EAN: 5453001615622
📦 Package Contents
