This large 240 cm six-panel satellite dish is designed for demanding satellite reception across both C-band and Ku-band. Its large reflector surface provides very high gain and a strong reception margin for satellites and signals that are difficult to receive using smaller dishes.
The reflector consists of six separate sheet-metal panels that are assembled at the installation site. The sectional construction simplifies transport, storage and handling compared with a one-piece satellite dish of the same diameter.
The dish provides a specified gain of 38.39 dB at 4.0 GHz in C-band and 48.04 dB at 12.5 GHz in Ku-band. Its aperture efficiency is 75%, with a focal length of 91.5 cm and an F/D ratio of 0.38.
The product is supplied with a fixed stand for permanent installation. Elevation can be adjusted from 0 to 90 degrees, while azimuth can be adjusted through 360 degrees. The construction is intended for a fixed installation and does not include a motor mount.
The LNB and LNB holder are not included. A compatible LNB holder is available separately under product number 3637.
✅ Product Benefits
- Large 240 cm reflector diameter
- Designed for both C-band and Ku-band reception
- Very high gain for demanding satellite signals
- 38.39 dB gain at 4.0 GHz
- 48.04 dB gain at 12.5 GHz
- 75% aperture efficiency
- Reflector divided into six separate panels
- Easier to transport and handle than a one-piece 240 cm dish
- Assembled at the installation site
- Supplied with a fixed stand
- Elevation adjustment from 0 to 90 degrees
- Full 360-degree azimuth adjustment
- Polyester powder-coated finish
- Light-grey colour
- Operating temperature from −40 to +60°C
- Designed for permanent and professional installations
🎯 Ideal For
- C-band satellite reception
- Ku-band satellite reception
- Weak or difficult-to-receive satellite positions
- International satellite channels
- Professional satellite systems
- Technical experiments and advanced satellite reception
- Permanent ground installations
- Systems requiring very high antenna gain
- Locations where a standard 80–150 cm dish cannot provide sufficient signal
- Satellite enthusiasts and specialist installations
🔧 Installation
The dish consists of six reflector panels that must be assembled at the installation site. All panels must be aligned carefully so that they form a smooth and correctly shaped reflector surface.
Position the supplied stand on a stable, level and properly dimensioned foundation. Because of the antenna’s large diameter and substantial wind exposure, the stand must be securely anchored according to the supporting surface and local wind conditions.
After assembling the reflector and stand, install a suitable LNB holder and LNB for the required frequency band. The LNB and LNB holder are not included. A compatible LNB holder is available separately under product number 3637.
Carefully align the dish in both azimuth and elevation. Because a 240 cm reflector has a narrow reception beam, a professional satellite signal meter is recommended for accurate alignment.
Professional installation and a properly engineered foundation are strongly recommended.
⚙️ Technical Specifications
Product type: Large sectional satellite dish
Antenna design: Prime-focus satellite dish
Reflector construction: Six separate panels
Number of panels: 6
Diameter: 240 cm
Focal length: 91.5 cm
F/D ratio: 0.38
Aperture efficiency: 75%
C-band gain at 4.0 GHz: 38.39 dB ±1 dB
Ku-band gain at 12.5 GHz: 48.04 dB ±1 dB
Elevation range: 0–90°
Azimuth adjustment: 0–360°
Compatible pole diameter: 75 mm
Standard mounting codes according to product data: G/P/W
Installation type: Fixed permanent installation
Stand: Fixed stand included
Motor mount: Not included
Surface finish: Polyester powder coating
Colour: Light grey/Cool Grey
Ambient temperature: −40 to +60°C
Relative humidity: 0–100%
LNB: Not included
LNB holder: Not included, sold separately
Compatible LNB holder: Product number 3637
📦 Package Contents
- 6 × Reflector panels forming one 240 cm satellite dish
- 1 × Fixed stand for permanent installation
- Feed-support rods and braces shown in the product images
- Fasteners and assembly components for the satellite dish
Please note: LNB, LNB holder, motor mount, motor-control equipment, coaxial cable, connectors, satellite receiver, foundation and anchoring materials are not included.
🔧 Compatible Accessories
- LNB holder, product number 3637
- C-band LNB or LNBF
- Ku-band LNB or LNBF
- Combined C-/Ku-band reception solution
- 75-ohm coaxial cable for satellite installations
- F-connectors or compression connectors
- Satellite receiver for the required frequency band
- DiSEqC switch
- Earthing and equipotential bonding components
- Foundation and anchoring materials
- Professional satellite signal meter
⚠️ Important Information
- The LNB and LNB holder are not included.
- A compatible LNB holder is sold separately under product number 3637.
- This product is intended for a fixed and permanent installation.
- Motor brackets and motor-control equipment are not included.
- This product is supplied as bulky freight.
- Confirm the freight cost and delivery options before ordering.
- The dish has a diameter of 240 cm and requires a large, unobstructed installation area.
- The fixed stand must be anchored to a properly engineered foundation.
- Wind loading will be substantial because of the antenna’s large reflector surface.
- The foundation and anchoring system must be designed according to local wind, ground and building conditions.
- Do not install the antenna where it could cause injury or property damage if it becomes detached.
- All six panels must be assembled and aligned accurately to achieve the specified performance.
- The selected LNB and feed must suit C-band or Ku-band operation and the dish’s 0.38 F/D ratio.
- Follow local requirements for planning permission, earthing, equipotential bonding and lightning protection.
- Inspect the installation’s fasteners, braces and anchors regularly.
- Professional installation is strongly recommended.
